搜索

HC-05 6 Pin Wireless Bluetooth RF Transceiver Module Serial BT Module for Arduino

Click

Click

HC-05 6 Pin Wireless Bluetooth RF Transceiver Module Serial BT Module for Arduino

stock quantity :

Select the number of specifications

Please check the product information you want!

产品详情 Product Evaluation

Module parameters: 
1.PCB Size: 37.3mm (Long) *15.5mm (wide) 
2. Weight: 3.5g
3. Input voltage: 3.6V--6V, prohibit exceeding 7V
4. Leads 6 feet: EN/VCC/GND/RXD/TXD/STATE (Bluetooth state leads, not connected output low level, the output high level after connection) 
5. With the connection status indicator, LED flash indicates no Bluetooth connection; Led slow flash indicates enter at command mode
6. On-board 3.3V voltage regulator chip, input voltage DC 3.6V-6V; When not paired, current about 30mA (due to LED lights flashing, current in the state of change); After the pairing succeeds, the current is about 10mA
7. Effective transmission distance of 10 meters in open area, more than 10 meters is possible, but not to ensure the quality of the connection
8. After pairing succeeds, can be used as full duplex serial port. No need to understand any Bluetooth protocol, but only support 8-bit data bits, 1-bit stop bits, no parity communication format. This is also the most commonly used communication format, does not support other formats! 
9. Press the key and then power up the Bluetooth module to enter at mode, set parameters and query information
10. Can switch host and machine mode from at command
11. The module default baud rate is 9600, the default pairing password is 1234, the default name is HC-05
Wiring method: 
VCC: Connect the power supply positive
GND: Connecting the cathode
RXD: The receiver, the Bluetooth module receives data from other devices, and the sending end TXD of the other devices normally
TXD: Send end, Bluetooth module sends data to other equipment; the receiving end RXD of the other equipments normally
En: To enable the end, need to enter the at mode when 3.3V

Note: this item doesn't works with iOS.

No comment

产品详情

Module parameters: 
1.PCB Size: 37.3mm (Long) *15.5mm (wide) 
2. Weight: 3.5g
3. Input voltage: 3.6V--6V, prohibit exceeding 7V
4. Leads 6 feet: EN/VCC/GND/RXD/TXD/STATE (Bluetooth state leads, not connected output low level, the output high level after connection) 
5. With the connection status indicator, LED flash indicates no Bluetooth connection; Led slow flash indicates enter at command mode
6. On-board 3.3V voltage regulator chip, input voltage DC 3.6V-6V; When not paired, current about 30mA (due to LED lights flashing, current in the state of change); After the pairing succeeds, the current is about 10mA
7. Effective transmission distance of 10 meters in open area, more than 10 meters is possible, but not to ensure the quality of the connection
8. After pairing succeeds, can be used as full duplex serial port. No need to understand any Bluetooth protocol, but only support 8-bit data bits, 1-bit stop bits, no parity communication format. This is also the most commonly used communication format, does not support other formats! 
9. Press the key and then power up the Bluetooth module to enter at mode, set parameters and query information
10. Can switch host and machine mode from at command
11. The module default baud rate is 9600, the default pairing password is 1234, the default name is HC-05
Wiring method: 
VCC: Connect the power supply positive
GND: Connecting the cathode
RXD: The receiver, the Bluetooth module receives data from other devices, and the sending end TXD of the other devices normally
TXD: Send end, Bluetooth module sends data to other equipment; the receiving end RXD of the other equipments normally
En: To enable the end, need to enter the at mode when 3.3V

Note: this item doesn't works with iOS.

Product Evaluation

No comment

HC-05 6 Pin Wireless Bluetooth RF Transceiver Module Serial BT Module for Arduino
Long press to look detail
Long by picture save/share

HC-05 6 Pin Wireless Bluetooth RF Transceiver Module Serial BT Module for Arduino

Add To Cart
INQUIRY

enquiry form:

  • Please enter the verification code

enquiry content:


You have no items to require

Add Successfully

About Us

 

HiLetgo is located in China. We are a Big & Professional Electronics Modules, Sensors and Robort Parts Manufacturer, we have our own Brand "HiLetgo",  products including Develop Boards like Uno, MEGA, Pro mini, Nano, ESP8266, ESP32, Power & Drive modules, Sensors, Breadboards, Connectors and Jumper Wires etc.We are committing ourselves to provide the Newest products with High quality and competitive price to the people at all over the world!

 

Shenzhen HiLetgo Technology Co., Ltd

Shenzhen HiLetgo E-Commerce Co., Ltd

Tel: +86-0755-36625387          Fax: +86-0755-36625387

Mobile: +86-13066806553     WhatsAPP: +86-13066806553

WeChat: L13066806553           E-mail: sales@hiletgo.com 

Skype: jelly0115                      Website: www.hiletgo.com 

Add: Room 1323-1327, Huanqiu Wuliu Zhongxin, HuaNanCheng, PingHu, LongGang, Shenzhen, Guangdong, China. 518111 

                                                                                                                                          @Copyright 2018 Shenzhen HiLetgo Technology Co., Limited

添加微信好友,详细了解产品
使用企业微信
“扫一扫”加入群聊
复制成功
添加微信好友,详细了解产品
我知道了